This is to demonstrate to Miele customer services what appears to be a serious flaw with their 2010 induction hob control panel. Several Miele engineers have lo. A Miele authorized service technician in accordance with national and local safety regulations and the provided installation instruc-tions. Contact Miele’s Technical Service Department for examination, repair or adjustment. Repairs and other work by unauthorized per-sons. Ceramic hobs with induction To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. Miele cannot be held liable for damage caused by non-compliance. Ceramic cooktops with induction To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. En - AU, NZ M.-Nr.

We have collected all the error codes of Miele induction cookers with a detailed description of the causes of malfunctions, diagnostics and repair. For convenience, arranged in a convenient and understandable table below.

The models with the display show the alphanumeric combination on your display, find it in the table and find out the reason for the error.

Miele Induction Lc Error 1007

Miele Induction Hob Lc Error

Models without a display do not execute the specified program and according to the lit or flashing lights placed on the control panel, you can find out the problem.

Miele induction cookers errors, decoding

Miele Induction Lc Error 1002

Error code	Description	Causes and solution
LC	Active power-on lock and / or normal.	Depending on the model, you need to hold down the “+” and “-” or “lock” and “0” buttons. Hold down the key combination until a distinctive beep sounds.
dE	The panel works in demo mode.	To turn off the demo mode, go into programming and select “S1”. Call a professional to solve the problem.
FE37	Active heat protection.	Try another cookware. If protection does not turn off, contact service.
FE44	Panel protection is included.	Perhaps you are using the wrong dishes, try replacing them. Reduce the power of the burner; if this does not help, contact a service center.
FE47	Overheating hob.	Check the gaps between the panel and the shelf (at least 1.5 cm wide). Try to turn it on again, if it doesn’t help, you need help from a service center.
FE48	The working area of the panel is overheating.	Perhaps the installation work is broken, the cooling mechanism is defective. Try restarting the device or contact a specialist.
FE49	Burner cooling does not work.	The device overheats due to errors made during installation. The cooler (fan) may be damaged.
FE00	Launch lock or regular lock activated.	To deactivate, you need to turn off the power or, depending on the model, hold down the following buttons: + and -, L and C, “lock” and “0”.
FE04	Demo mode is on.	To turn off the demo mode, hold the touch buttons “0” on the left and “2” on the right, hold 6 seconds until disconnected.
FE08	Overheat protection tripped.	The mechanism works if they put empty dishes or inappropriate. Turn off electrical equipment, let it cool. Consult a specialist about replacing a fan.
FE12	The protective mechanism against overheating is activated.	The protective mechanism works in such cases: failure of the cooler and non-compliance of the ventilation with the norms. Remove foreign objects from the device.
FE16	Overheating hob.	Correct the lack of installation, increase the ventilation gaps (at least 1.5 cm). Maybe there are problems with the cooler. Reduce power on electric burners during operation.
FE76	Critically high temperature.	The problem with overheating is not always the malfunction of the cooler. Round bottom dishes also activate protection. Narrow ventilation gaps do not allow air to circulate and the equipment does not cool down.
FE01	The permissible temperature on the device has been exceeded.	Weak cooler, poor ventilation are common causes of insufficient cooling. Call service in order to repair the fan.
FE02	The problem is programming.	The computer may crash due to violations of the rules when connected. Try turning the device off and on again, if the breakdown code lights up on the display, call the wizard for flashing.
FE03	Programming failed.	This is a serious malfunction related to the motherboard. You can only disconnect the device from the power supply and wait for the arrival of a specialist for further repairs.
FE05	Violations in the programming.	Most likely the firmware or the entire motherboard flew. You must disconnect the equipment from the network, immediately call the flashing specialist, do not take any action.
FE06	Crash in touch switch programming.	Due to a malfunction of the motherboard, the firmware flashed. Need intervention service. There they can not only identify the cause of the breakdown, but also eliminate its repetition.
FE07	The functioning of the motherboard is broken.	Incorrect connection of equipment, violation of installation requirements are the reasons for the crashed software. Urgently call specialists from the repair company.
FE09	The firmware has flown.	The software crashes in case of improper connection of equipment, burnout of the motherboard. It is necessary to call an employee from a service technician.
FE10	Does not respond to pressing “-” of the front left electric burner.	The signal transmission area does not respond well to pressure due to stains of fat - wipe the ceramics. If the contact is poor, a breakdown of insulation has occurred and the services of a repair service organization will be needed.
FE11	The “+” front left does not work.	It is necessary to wipe on the pure glass ceramics and buttons with automation. If the problem persists, contact a service center to diagnose and replace the sensor sensors.
FE13	The front left burner booster does not function.	Perhaps you have not cleaned the glass ceramics, and the automation slows down dirt and spilled liquid. Wipe clean the equipment and try to press the button again.
FE14	“-” The rear left does not function well.	The cause of the malfunction may be a lack of cleanliness of glass ceramics or a breakdown in the isolation of the switch. Polish the work area, if it does not work, contact a specialist from a service company.
FE15	Defective '+', rear left electric burner.	Due to contamination, the tactile contact between the ceramic surface and the meter may be disturbed. Wipe the ceramics clean after every cooking.
FE17	The rear left burner booster does not work.	Failure of an emergency increase in power can be triggered by a breakdown of insulation on the meter. Wipe the ceramic thoroughly; call a repair technician to diagnose the sensor.
FE18	The “-' central burner has failed.	Burning the meter on the transmitter makes the push button malfunctioning. Inspect the display for cracks and chips, for water to leak. If you notice something, call a service company.
FE19	The “+” central burner does not respond.	The switch may have blown, contact your service provider to replace it. There are frequent cases when the “+” does not function due to pollution.